行业新闻

当前位置:首页 > 新闻中心 > 行业新闻 >

山东制氮机常见的故障处理方式

来源:https://www.sdqyjn.com/   日期:2020-10-23   浏览量:
TAG:山东制氮机,山东干燥机,山东螺杆鼓风机,山东空压机,山东自动排水器

制氮机设备在运行时难免会出现故障,制氮机喷筛及碳分子筛粉化就是制氮机在使用过程中一个比较常见的故障,今天山东制氮机制厂家的小编为您介绍下:

It is inevitable that the nitrogen generator equipment will break down when it is running. The spray screen and carbon molecular sieve pulverization of the nitrogen generator are common faults in the use of the nitrogen generator. The editor of Shandong nitrogen making mechanism manufacturer will introduce the following for you:

制氮机的控制系统:

Control system of nitrogen generator:

1、电气控制系统:由PLC、电路系统、仪表、阀门组成。

1. Electrical control system: composed of PLC, circuit system, instrument and valve.

2、空气缓冲罐:由空气储罐、阀门等组成,主要用于保证用气的平稳。

2. Air buffer tank: composed of air storage tank, valve, etc., it is mainly used to ensure the stable use of gas.

3、氮气缓冲罐:由氮气储罐、阀门组成,储存氮气,主要是保证用气的平稳。

3. Nitrogen buffer tank: it is composed of nitrogen storage tank and valve to store nitrogen, mainly to ensure the stable use of gas.

4、制氮机主机:由两个装满碳分子筛的吸附塔和自动控制阀门组成,可以说是制氮机的核心。

20201023923560.jpg

4. Main engine of nitrogen generator: it is composed of two adsorption towers filled with carbon molecular sieve and automatic control valve, which can be said to be the core of nitrogen generator.

5、空气净化系统:由冷干机、过滤器、除油过滤器等组成,主要用于净化空气,除尘除水除油。

5. Air purification system: it is composed of cold dryer, filter and oil removal filter. It is mainly used to purify air, remove dust, water and oil.

随着制氮机的分子筛压力磨擦和使用时间的增加,制氮机分子筛寿命也随之减少,时间一长分子筛就容易产生粉化的现象。特别容易发生在以气缸压紧的制氮机上、弹簧压紧的制氮机上也容易发生此类故障,虽说椰垫法兰压紧不可监控,但是制氮机出厂之前,生产厂家在碳分子筛装填过程中会十分小心,并有专用的压紧工具和压紧方法,反而产生制氮机碳分子筛粉化,喷筛的故障反而更低!

With the increase of pressure friction and service time of molecular sieve in nitrogen generator, the service life of molecular sieve of nitrogen generator is also reduced, and the phenomenon of pulverization is easy to occur over a long time. It is especially easy to occur on the nitrogen generator compressed by cylinder and spring. Although the coconut gasket flange pressing can not be monitored, the manufacturer will be very careful in the loading process of carbon molecular sieve before the nitrogen generator leaves the factory, and there are special pressing tools and pressing methods. On the contrary, the carbon molecular sieve of the nitrogen generator will be powdered, and the fault of sieve spraying will be on the contrary Lower!

制氮机喷筛、制氮机碳分子筛粉化直接的现象就是制氮机现场一片乌黑,再次因为碳分子筛价格昂贵,粉化的碳分子筛不可以再次被使用,重新购买新分子筛又是一笔费用,碳分子筛粉化还会造成制氮机管道阀门磨损严重,造成制氮机系统串气,吸附压力上不来氮气指标严重不足。

The phenomenon of direct pulverization of carbon molecular sieve in nitrogen generator and spray sieve in nitrogen generator is that the site of nitrogen generator is black. Again, because carbon molecular sieve is expensive, powdered carbon molecular sieve can not be used again. It is also a cost to purchase new molecular sieve. Pulverization of carbon molecular sieve will cause serious wear of pipeline valve of nitrogen generator, resulting in air entrainment in nitrogen generator system and no nitrogen on adsorption pressure The gas index is seriously insufficient.

以上就是小编为您介绍的山东制氮机喷筛故障的原因,希望为大家带来帮助!如需了解更多的精彩内容请关注公司网站:https://www.sdqyjn.com

The above is the reason for the failure of spray screen of Shandong nitrogen machine introduced by Xiaobian. I hope to help you! For more information, please visit our website: https://www.sdqyjn.com



上一篇:干燥机的出口露点不合格的原因?
下一篇:选择空气机要求的规格和要求有哪些?