制氮机第一次开机应该注意哪些问题？

制氮机大家都是比较熟悉，是以空气为原材料把空气中的氮气和氧气进行分离的一种制氮设备，很多人都会对制氮设备进行操作。然而很多人往往因为太熟悉了就会忽视制氮设备的第一次开机这个因素，下面山东制氮机的小编就来给广大用户简单的介绍下制氮设备第一次开机应该要注意什么，下面就一起来看看吧。

Everyone is familiar with the nitrogen generator. It is a kind of nitrogen making equipment which uses air as raw material to separate nitrogen and oxygen in the air. Many people will operate the nitrogen making equipment. However, many people tend to ignore the factor of the first start-up of nitrogen generation equipment because they are too familiar with it. The following editor of Shandong nitrogen generator will give a brief introduction to what should be paid attention to when the nitrogen generating equipment is started for the first time. Let's have a look at it.

先查看体系阀门（开。关）的方位，空压机出口节门常开，制氮机进口节门关增压机进出水节门均关，氮气储罐进时令门关。体系通电 3.先接通制氮机，等外表呈现数值后，把温度表上的温度值设定到40℃纯度表上的纯度值设定到0.6。

First check the system valve (on. The outlet throttle valve of the air compressor is normally open, the inlet throttle valve of the nitrogen generator is closed, the inlet and outlet water throttle valves of the booster are all closed, and the valve is closed when the nitrogen storage tank enters. Turn on the nitrogen generator first, and set the temperature value on the thermometer to 40 ℃ and the purity value on the purity meter to 0.6.

开冷干机，并使其作业1—2分钟，一起看一看蒸发表不能为零。开空压机，使空气罐罐内压力在1、1MPa以上时，翻开制氮机进口节门。把制氮机的采样流量计调到1.5摆布。 7.把增压机进水节门翻开，并把添加机两个上节门翻开，使水柱在50mm摆布，并关上节门，翻开排水阀，再翻开氮气储罐进时令门。

Turn on the cold dryer and let it work for 1-2 minutes. Let's have a look at the evaporation meter, which can't be zero. Open the air compressor to open the inlet throttle of nitrogen generator when the pressure in the air tank is above 1 and 1MPa. Adjust the sampling flowmeter of nitrogen generator to 1.5 pendulum. 7. Open the water inlet throttle of the booster and the two upper throttle valves of the adding machine to make the water column swing at 50 mm. Close the throttle valve, open the drain valve, and open the timing valve of the nitrogen storage tank.

当氮气机上的氮气灯亮时，（纯度上的实践值低于设定值），敞开增压机。当增压机把氮气储罐打满后，增压机自停，再把制氮机上温度表的温度设定到0℃时，符温度表实践温度降低30℃以下，（夏天到室温），将制氮机进口节门封闭。

When the nitrogen lamp on the nitrogen machine is on (the actual value of purity is lower than the set value), open the booster. When the supercharger fills up the nitrogen storage tank, the supercharger stops automatically, and then sets the temperature of the thermometer on the nitrogen generator to 0 ℃, the actual temperature of the thermometer is reduced below 30 ℃ (from summer to room temperature), and the inlet throttle of the nitrogen generator is closed.