公司新闻

当前位置:首页 > 新闻中心 > 公司新闻

制氮机是如何对碳分子筛进行简易转化?

来源:https://www.sdqyjn.com/   日期:2021-03-04   浏览量:0
TAG:山东制氮机,山东干燥机,山东螺杆鼓风机,山东空压机,山东自动排水器

碳分子筛的更换是耗材问题的解决,考虑到制氮机工作上的特性,因此我们在进行转化的时候需要用到简易的方法,下面就让山东制氮机厂家的小编为你详细介绍下制氮机是如何对碳分子筛进行简易转化的?

The replacement of carbon molecular sieve is the solution to the problem of consumables. Considering the working characteristics of the nitrogen generator, we need to use a simple method when we carry out the conversion. Let's let the editor of Shandong nitrogen generator manufacturer introduce in detail how the nitrogen generator carries out the simple conversion of carbon molecular sieve?

1、电源被切断。取代碳分子筛的制氮机安全运行的前提是先切断电源!记住这一点。停止供应压缩空气,卸载制氮机系统内部压力,直至所有压力表归零,并切断系统电源。

  1. The power was cut off. The prerequisite for the safe operation of the nitrogen generator replacing carbon molecular sieve is to cut off the power first! Remember this. Stop the supply of compressed air, unload the internal pressure of the nitrogen generator system until all pressure gauges return to zero, and cut off the power supply of the system.

  2. 20210304563855.jpg

2、卸下制氮机吸附塔的顶盖,提前准备好拆卸扳手!

2. Remove the top cover of the adsorption tower of the nitrogen generator and prepare the spanner in advance!

3、取下制氮机不锈钢丝网!

3. Remove the stainless steel wire mesh of nitrogen generator!

4、清除工作完成后,加入3厘米厚的椰垫过滤,用直径为5MM的氧化铝在吸附塔底部预铺5厘米厚,然后进行碳分子筛装填。

4. After the removal, add 3 cm thick coconut mat for filtration, pre lay 5 cm thick alumina with diameter of 5 mm at the bottom of the adsorption tower, and then carry out carbon molecular sieve loading.

5、填充至顶部,用锤子或振动设备振动吸附塔,使碳分子筛之间的堆积密度达到620-640千克/立方米,更新顶部的椰垫和不锈钢丝网,覆盖吸附塔的顶部,用长螺栓紧固至常规位置,更新所有高于8.8的高强度螺栓。

5. Fill to the top, vibrate the adsorption tower with hammer or vibrating equipment to make the bulk density between the carbon molecular sieves reach 620-640 kg / m3, update the coconut mat and stainless steel wire mesh on the top, cover the top of the adsorption tower, fasten to the normal position with long bolts, and update all high strength bolts higher than 8.8.

6、复位后,调试制氮机。调试包括接头肥皂水的泄漏检测、工作状态和性能指标。请参考制氮机的操作说明!

6. After reset, debug the nitrogen generator. The debugging includes the leakage detection, working state and performance index of the joint soapy water. Please refer to the operating instructions of the nitrogen generator!

更多关于制氮机的讯息,欢迎登录网址进行详细了解https://www.sdqyjn.com

For more information about nitrogen generator, please visit our website for more information https://www.sdqyjn.com


上一篇:购买螺杆鼓风机应该考虑的价格组成部分
下一篇:空压机在打地热井洗井中的应用